Strict Standards: Non-static method phpbb_feed_factory::init() should not be called statically in /home/bigroadblues/bigroadblues.com/forum/feed.php on line 66
[phpBB Debug] PHP Notice: in file /feed.php on line 171: Cannot modify header information - headers already sent by (output started at /feed.php:66)
[phpBB Debug] PHP Notice: in file /feed.php on line 172: Cannot modify header information - headers already sent by (output started at /feed.php:66)
Big Road Blues Discussion Forums 2010-01-09T15:06:35+00:00 http://www.bigroadblues.com/forum/feed.php?f=13&t=10539 2010-01-09T15:06:35+00:00 http://www.bigroadblues.com/forum/viewtopic.php?t=10539&p=101437#p101437 <![CDATA[Re: Need imput on harp mic. element]]> Statistics: Posted by DeFord Harp Slider — Sat Jan 09, 2010 3:06 pm


]]>
2010-01-09T13:28:42+00:00 http://www.bigroadblues.com/forum/viewtopic.php?t=10539&p=101436#p101436 <![CDATA[Re: Need imput on harp mic. element]]> Peace to all, Ken

Statistics: Posted by Pastor Harmonica — Sat Jan 09, 2010 1:28 pm


]]>
2009-12-30T02:49:17+00:00 http://www.bigroadblues.com/forum/viewtopic.php?t=10539&p=101078#p101078 <![CDATA[Re: Need imput on harp mic. element]]> Statistics: Posted by jbone1 — Wed Dec 30, 2009 2:49 am


]]>
2009-12-29T17:40:39+00:00 http://www.bigroadblues.com/forum/viewtopic.php?t=10539&p=101061#p101061 <![CDATA[Re: Need imput on harp mic. element]]>
Pastor Harmonica wrote:
Hey Gheumann, I didn't do anything to at all. Just ran it through a on/off switch into a 1/4 inch jack. It still sounds great.


OK - the specs you posted say it has a 600 ohm impedance. That is low impedance. There is an impedance mismatch between the mic and your amp and it is at least worth trying it with an impedance matching transformer. The way you have it wired, it is better than a standard modern low impedance mic - the way they're wired most people only end up getting half the signal if they cable it straight to an amp. You're getting 100% of the signal. However both the amp and the element were designed to operate within a range of impedance - and having them matched is USUALLY the best. It is fairly easy to try this and you can't hurt anything - so on the chance your mic could be even better - I suggest you try an impedance matching transformer. If you get a typical external one with XLR female at one end and 1/4" male at the other, then you'll want to wire your element to a cable with an XLR male plug. The signal should be on pins 2 and 3. Pin 2 should also be connected to Pin 1 and the shield for proper grounding.

/Greg

Statistics: Posted by gheumann — Tue Dec 29, 2009 5:40 pm


]]>
2009-12-28T11:58:08+00:00 http://www.bigroadblues.com/forum/viewtopic.php?t=10539&p=101015#p101015 <![CDATA[Re: Need imput on harp mic. element]]> Statistics: Posted by Pastor Harmonica — Mon Dec 28, 2009 11:58 am


]]>
2009-12-26T22:29:21+00:00 http://www.bigroadblues.com/forum/viewtopic.php?t=10539&p=101003#p101003 <![CDATA[Re: Need imput on harp mic. element]]> Statistics: Posted by gheumann — Sat Dec 26, 2009 10:29 pm


]]>
2009-12-25T13:19:16+00:00 http://www.bigroadblues.com/forum/viewtopic.php?t=10539&p=100974#p100974 <![CDATA[Re: Need imput on harp mic. element]]> Statistics: Posted by Pastor Harmonica — Fri Dec 25, 2009 1:19 pm


]]>
2009-12-24T23:10:43+00:00 http://www.bigroadblues.com/forum/viewtopic.php?t=10539&p=100969#p100969 <![CDATA[Re: Need imput on harp mic. element]]> Statistics: Posted by gheumann — Thu Dec 24, 2009 11:10 pm


]]>
2009-12-24T14:43:36+00:00 http://www.bigroadblues.com/forum/viewtopic.php?t=10539&p=100953#p100953 <![CDATA[Re: Need imput on harp mic. element]]> Statistics: Posted by Pastor Harmonica — Thu Dec 24, 2009 2:43 pm


]]>
2009-12-24T00:05:10+00:00 http://www.bigroadblues.com/forum/viewtopic.php?t=10539&p=100938#p100938 <![CDATA[Re: Need imput on harp mic. element]]>
www.myspace.com/shakeylyman

Statistics: Posted by bottleneck — Thu Dec 24, 2009 12:05 am


]]>